Nissan Rogue Owners Manual: Ignition switch (if so equipped)

Nissan Rogue Owners Manual / Starting and driving / Ignition switch (if so equipped)

WARNING

Never remove or turn the key to the LOCK position while driving. The steering wheel will lock (for models with a steering lock mechanism). This may cause the driver to lose control of the vehicle and could result in serious vehicle damage or personal injury.
Never place the ignition switch in the LOCK position while driving. The steering wheel will lock (for models with a steering lock mechanism). This may cause the driver to lose control of the vehicle and could result in serious vehicle damage or personal injury.

Continuously Variable Transmission (CVT)

The ignition lock is designed so that the ignition switch cannot be turned to the LOCK position until the shift lever is moved to the P (Park) position.

When moving the ignition switch to the LOCK position, make sure the shift lever is in the P (Park) position.
When removing the key from the ignition switch, make sure the shift lever is in the P (Park) position.

When the ignition switch cannot be turned to the LOCK position:

Shift the shift lever to the P (Park) position.
Turn the ignition switch slightly in the ON direction.
Turn the ignition switch to the LOCK position.
Remove the key if it is inserted in the ignition switch.

If the ignition switch is turned to the LOCK position, the shift lever cannot be moved from the P (Park) position.

The shift lever can be moved if the ignition switch is placed in the ON position and the foot brake pedal is depressed.

Key positions

LOCK: Normal parking position (0)

OFF: (Not used) (1)

This position activates electrical accessories such as the radio when the engine is not running.

ON: Normal operating position (3)

This position turns on the ignition system and the electrical accessories.

START: (4)

This position starts the engine. As soon as the engine has started, release the key. It automatically returns to the ON position.

NISSAN vehicle immobilizer system

The NISSAN Vehicle Immobilizer system will not allow the engine to start without the use of the registered key.

If the engine fails to start using a registered key (for example, when interference is caused by another registered key, an automated toll road device or automatic payment device on the key ring), restart the engine using the following procedure:

Leave the ignition switch in the ON position for approximately 5 seconds.
Place the ignition switch in the OFF or LOCK position, and wait approximately 10 seconds.
Repeat Steps 1 and 2.
Restart the engine while holding the device (which may have caused the interference) separate from the registered key.

If the no start condition re-occurs, NISSAN recommends placing the registered key on a separate key ring to avoid interference from other devices.

Driving safety precautions

Your NISSAN is designed for both normal and off-road use. However, avoid driving in deep water or mud as your NISSAN is mainly designed for leisure use, unlike a conventional off-road vehicle. R ...

Push-Button Ignition Switch (if so equipped)

WARNINGDo not operate the push-button ignition switch while driving the vehicle except in an emergency. (The engine will stop when the ignition switch is pushed 3 consecutive times ...

Other materials:

Periodic maintenance
IDLE SPEED Inspection 1.CHECK IDLE SPEED With CONSULT Check idle speed in “DATA MONITOR” mode of “ENGINE” using CONSULT. With GST Check idle speed with Service $01 of GST. >> INSPECTION END IGNITION TIMING Inspection 1.CHECK IGNITION TIMING Attach timing light (A) to th ...

Cup holders
Front console Bench seat CAUTIONDo not recline the rear seatback when you use the cup holders on the rear armrest. Doing so may cause the beverages to spill over, and if they are hot, they may scald the passengers. CAUTION Avoid abrupt star ...

C1105, C1106, C1107, C1108 wheel sensor
DTC Logic DTC DETECTION LOGIC DTC Display Item Malfunction detected condition Possible causes C1105 RR RH SENSOR-2 When distance between rear wheel sensor RH and rear wheel sensor RH rotor is large. When installation of rear whe ...