Nissan Rogue Service Manual: Steering wheel turning force is heavy or light
Description
Steering wheel turning force is heavy or light.
Diagnosis Procedure
1.PERFORM SELF-DIAGNOSIS
With CONSULT
- Turn the ignition switch OFF to ON.
- Perform “EPS” self-diagnosis.
Is any DTC detected? YES >> Check the DTC. Refer to STC-13, "DTC Index".
NO >> GO TO 2.
2.CHECK THE ILLUMINATION OF THE EPS WARNING LAMP
Check that the EPS warning lamp turns ON when ignition switch turns ON. Then, EPS warning lamp turns OFF after the engine is started.
Is the inspection result normal? YES >> GO TO 3.
NO >> Perform trouble diagnosis of EPS warning lamp. Refer to STC-28, "Diagnosis Procedure".
3.CHECK EPS CONTROL UNIT SIGNAL (1)
With CONSULT
- Start the engine.
CAUTION: Never drive the vehicle.
- Select “ASSIST LEVEL” in “DATA MONITOR” in “EPS”.
Dose the item in “DATA MONITOR” indicate “100%”? YES >> GO TO 6.
NO >> GO TO 4.
4.CHECK EPS CONTROL UNIT SIGNAL (2)
With CONSULT
Select “BATTERY VOLT” in “DATA MONITOR” in “EPS”.
Dose the item in “DATA MONITOR” indicate “10.5 V” or more? YES >> GO TO 5.
NO >> Perform trouble diagnosis of EPS control unit power supply and ground. Refer to STC-20, "Diagnosis Procedure".
5.CHECK EPS CONTROL UNIT SIGNAL (3)
With CONSULT
- Select “ASSIST LEVEL” in “DATA MONITOR” in “EPS”.
- Stop the EPS system until the item in “DATA MONITOR” becomes
“100%” or less.
NOTE: While stopping the EPS system, do not turn steering wheel.
- Check that the symptom continues.
Dose the symptom continue? YES >> GO TO 6.
NO >> The assist torque decreases because of protection function. This is not malfunction. Inspection End.
6.CHECK EPS CONTROL UNIT SIGNAL (4)
With CONSULT
- Start the engine.
CAUTION: Never drive the vehicle.
- Turn steering wheel from full left stop to full right stop.
- Select “TORQUE SENSOR” in “DATA MONITOR” in “EPS”.
Is the inspection result normal? YES >> GO TO 8.
NO >> GO TO 7.
7.CHECK EPS MOTOR
Perform the trouble diagnosis of EPS motor. Refer to STC-24, "Diagnosis Procedure".
Is the inspection result normal? YES >> GO TO 8.
NO >> Repair or replace the specific malfunctioning part.
8.CHECK STEERING WHEEL TURNING FORCE
Check the steering wheel turning force. Refer to ST-7, "Inspection".
Is the inspection result normal? YES >> Inspection End.
NO >> Check the steering wheel turning force for mechanical malfunction. Refer to ST-7, "Inspection".
EPS warning lamp does not turn off
Description
EPS warning lamp does not turn OFF several seconds after engine started.
Diagnosis Procedure
1.PERFORM SELF-DIAGNOSIS
With CONSULT
Turn the ignition switch OFF to ON.
...
Unbalance steering wheel turning force and return between
right and left
Description
Unbalance steering wheel turning force and return between right and left.
Diagnosis Procedure
1.CHECK THE ILLUMINATION OF THE EPS WARNING LAMP
Check the EPS warning lamp while engine i ...
Other materials:
Symptom diagnosis
NISSAN VEHICLE IMMOBILIZER SYSTEM-NATS SYMPTOMS
Symptom Table
NOTE:
Before performing the diagnosis in the following table, check
“SEC-150, "Work Flow"”.
Check that vehicle is under the condition shown in “Conditions
of vehicle” before starting diagnosis, ...
C1604 torque sensor
DTC Logic
DTC DETECTION LOGIC
DTC
Display item
Malfunction detected condition
Possible cause
C1604
TORQUE SENSOR
When torque sensor output signal is malfunctioning.
Harness or connector
Torque sensor
EPS control unit
...
ID registration cannot be completed
Description
The ID of the tire pressure sensor installed in each wheel cannot be
registered in the tire pressure monitoring
system. Inspect the tire pressure sensor or the tire pressure monitoring system
circuit.
Diagnosis Procedure
1.CHECK TIRE PRESSURE SENSOR ACTIVATION TOOL
Check tire pr ...