Nissan Rogue Service Manual: Preparation

Nissan Rogue Service Manual / Transmission & driveline / Driveline / Rear final drive: R145 / Preparation

Special Service Tools

The actual shapes of TechMate tools may differ from those of special service tools illustrated here.

Tool number (TechMate No.) Tool name		Description
KV38100200 (J-26233) Drift a: 65 mm (2.56 in) dia. b: 49 mm (1.93 in) dia.		Installing drive pinion oil seal Installing side oil seal
ST27861000 ( — ) Drift a: 62 mm (2.44 in) dia. b: 52 mm (2.05 in) dia.		Installing drive pinion oil seal
ST35271000 (J-26091) Drift a: 72 mm (2.83 in) dia. b: 63 mm (2.48 in) dia.		Installing drive pinion oil seal
KV40100610 (J-26089) Drift a: 63 mm (2.48 in) dia. b: 54.3 mm (2.138 in) dia.		Removing and installing gear carrier and rear cover (2 pieces are used) Installing pinion front bearing inner race
ST33052000 ( — ) Adaptor a: 22 mm (0.87 in) dia. b: 28 mm (1.10 in) dia.		Removing side bearing inner race
KV40105020 ( — ) Drift a: 39.7 mm (1.563 in) dia. b: 35 mm (1.38 in) dia. c: 15 mm (0.59 in)		Installing side bearing inner race
KV38109500 ( — ) Drive pinion socket		Removing and installing drive pinion lock nut Measuring preload torque
KV38109400 ( — ) Pinion nut wrench		Removing and installing drive pinion lock nut
ST17130000 ( — ) Drift a: 31.8 mm (1.252 in) dia. b: 58 mm (2.28 in) dia.		Installing pinion rear bearing outer race
ST33230000 (J-25805-01) Drift a: 51 mm (2.01 in) dia. b: 41 mm (1.61 in) dia. c: 28.5 mm (1.122 in) dia.		Installing pinion front bearing outer race
ST23860000 ( — ) Drift a: 38 mm (1.50 in) dia. b: 33 mm (1.30 in) dia.		Installing pinion rear bearing inner race Installing pinion front bearing inner race
ST38220000 ( — ) Press stand a: 63 mm (2.48 in) dia. b: 65 mm (2.56 in)		Installing pinion front bearing inner race
ST3127S000 (J-25765-A) Preload gauge		Measuring preload torque
KV381086S1 ( — ) Dummy cover set 1. KV38108610 ( — ) Dummy cover 2. KV38108621 ( — ) Dummy cover spacer 3. KV38108630 ( — ) Dummy cover shim		Checking backlash Checking drive gear runout Checking tooth contact

Commercial Service Tools

Tool name		Description
Separator		Removing side bearing inner race Removing pinion rear bearing inner race
Puller		Removing side bearing inner race Removing pinion rear bearing inner race
Pin punch a: 4.5 mm (0.177 in) dia.		Removing and installing lock pin
Oil seal remover		Removing drive pinion oil seal
Power tool		Loosening bolts and nuts

Precaution

Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONE ...

System description

STRUCTURE AND OPERATION Sectional View Drive gear Side bearing Differential case Pinion mate shaft Side gear Pinion mate gear Drive pinion Collapsible spacer AWD solenoi ...

Other materials:

NISSAN vehicle immobilizer system
The NISSAN Vehicle Immobilizer system will not allow the engine to start without the use of the registered key. If the engine fails to start using a registered key (for example, when interference is caused by another registered key, an automated toll road device or automatic payment device o ...

Fuel pump
Description Sensor Input signal to ECM ECM Function Actuator Crankshaft position sensor (POS) Camshaft position sensor (PHASE) Engine speed* Fuel pump control Fuel pump relay↓ Fuel pump Battery Battery voltage* *: ECM determines the st ...

Oil seal
VALVE OIL SEAL VALVE OIL SEAL : Removal and Installation REMOVAL Remove camshafts. Refer to EM-64, "Removal and Installation". Remove valve lifters. Refer to EM-56, "Disassembly and Assembly". Rotate crankshaft, and set piston whose valve oil seal is t ...