Nissan Rogue Service Manual: Diagnosis system (EPS control unit)

Nissan Rogue Service Manual / Steering / Steering Control System / System description / Diagnosis system (EPS control unit)

CONSULT Function

FUNCTION

CONSULT can display each diagnostic item using the diagnostic test modes shown following

Diagnostic test mode	Function
ECU identification	The part number stored in the control unit can be read.
Self diagnostic result	Self-diagnostic results and freeze frame data can be read and erased quickly.*
Data monitor	Input/Output data in the EPS control unit can be read.

*: The following diagnosis information is erased by erasing.

DTC
Freeze frame data (FFD)

ECU IDENTIFICATION

Displays the part number stored in the control unit.

SELF-DIAG RESULTS MODE

Refer to STC-13, "DTC Index".

When “CRNT” is displayed on self-diagnosis result.

The system is presently malfunctioning.

When “PAST” is displayed on self-diagnosis result.

System malfunction in the past is detected, but the system is presently normal.

FREEZE FRAME DATA (FFD)

The following vehicle status is recorded when DTC is detected and is displayed on CONSULT.

Item name

Display item

IGN COUNTER (0 – 39)

The number of times that ignition switch is turned ON after the DTC is detected is displayed.

• When “0” is displayed: It indicates that the system is presently malfunctioning.
When except “0” is displayed: It indicates that system malfunction in the past is detected, but the system is presently normal.

NOTE: Each time when ignition switch is turned OFF to ON, numerical number increases in 1→2→3...38→39.

When the operation number of times exceeds 39, the number do not increase and “39” is displayed until selfdiagnosis is erased.

DATA MONITOR MODE

NOTE: The following table includes information (items) inapplicable to this vehicle. For information (items) applicable to this vehicle, refer to CONSULT display items.

Monitor item (Unit)	Remarks
BATTERY VOLT (V)	Displays the power supply voltage for EPS control unit.
TORQUE SENSOR (Nm)	Displays steering wheel turning force detected by torque sensor.
MOTOR CURRENT (A)	Displays the current value consumed by EPS motor.*1
MOTOR SIG (A)	Displays the current commanded value to EPS motor.
ASSIST TORQUE (Nm)	Displays assist torque of EPS motor being output by the electric power steering.
C/U TEMP (°C) or (°F)	Displays the temperature of the EPS control unit.
ASSIST LEVEL (%)	Normally displays 100%. In case of an excessive stationary steering, the assist curvature gradually falls. However, it return to 100% when left standing.*2
VEHICLE SPEED (km/h) or (MPH)	Vehicle speed is displayed from vehicle speed signal via CAN communication.*3
WARNING LAMP (On/Off)	EPS warning lamp control status is displayed.
ENGINE STATUS (Stop/Run)	Engine speed is displayed from engine status signal via CAN communication.

*1: Almost in accordance with the value of “MOTOR SIG”. It is not a malfunction though these values are not accorded when steering quickly.
*2: Normally displays 100%. In case of an excessive stationary steering, the assist curvature gradually falls.

However, it returns to 100% when left standing.
*3: It is not a malfunction, though it might not be corresponding just after ignition switch in turned ON.

System

EPS SYSTEM EPS SYSTEM : System Description SYSTEM DIAGRAM INPUT/OUTPUT SIGNAL Communicates the signal from each control unit via CAN communication. Control unit Signal statu ...

ECU diagnosis information

EPS CONTROL UNIT Reference Value VALUES ON THE DIAGNOSIS TOOL CAUTION: The output signal indicates the EPS control unit calculation data. The normal values will be displayed even in the event t ...

Other materials:

Low tire pressure warning lamp blinks
Description The low tire pressure warning lamp blinks when the power switch is turned ON. NOTE: The position of an inactive tire pressure sensor can be identified by checking the blinking timing of the low tire pressure warning lamp. Diagnosis Procedure 1.TIRE PRESSURE SENSOR ID REGISTRA ...

Power liftgate main switch
Power liftgate main switch The power liftgate operation can be turned on or off by the power liftgate main switch on the instrument panel. When the power liftgate main switch is pushed to the OFF position, the power operation is not available by the power liftgate switch on the liftgate ...

Flat towing for front wheel drive vehicle (if so equipped)
Towing your vehicle with all four wheels on the ground is sometimes called flat towing. This method is sometimes used when towing a vehicle behind a recreational vehicle, such as a motor home. CAUTION Failure to follow these guidelines can result in severe transmission dama ...