Nissan Rogue Service Manual: P0965 pressure control solenoid B

Nissan Rogue Service Manual / Transmission & driveline / Transaxle & Transmission / Dtc/circuit diagnosis / P0965 pressure control solenoid B

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms (Trouble diagnosis content)

DTC detection condition

P0965

PC SOLENOID B (Pressure Control Solenoid B Control Circuit Range Performance)

When any of 1 or 2 is satisfied and this state is maintained for 10 seconds:

When all of the following conditions are satisfied:

DTC other than the applicable DTC is not detected.
Engine speed: More than 625 rpm
Selector lever: Other than P/N position
CVT fluid temperature: More than -20°C (-4°F)
TCM power supply: More than 11 V
The difference between instruction pressure of primary pressure and 10-msec-ago instruction primary pressure is 0 MPa or more
Instruction pressure of primary pressure: 0.86 MPa or more
Instruction pressure of primary pressure - primary pressure: More than 1.2 MPa
When all of the following conditions are satisfied and this state is maintained for 1 second:

DTC other than the applicable DTC is not detected.
CVT fluid temperature: More than -20°C (-4°F)
Selector lever: Other than P/N position
Engine speed: More than 625 rpm
Instruction pressure of primary pressure: More than 2 MPa
Primary pressure: 0.4 MPa or less

When all of the following conditions are satisfied:

DTC other than the applicable DTC is not detected.
CVT fluid temperature: More than -20°C (-4°F)
Selector lever: Other than P/N position
TCM power supply: More than 11 V
When all of the following conditions are satisfied and this state is maintained for 5.5 seconds:

DTC other than the applicable DTC is not detected.
CVT fluid temperature: More than -20°C (-4°F)
Selector lever: Other than P/N position
Primary pressure - instruction pressure of primary pressure: 1.2 MPa or more

The difference between instruction pressure of primary pressure and 10-msec-ago instruction primary pressure is 0 MPa or more
Primary pressure - instruction pressure of primary pressure: More than 1.2 MPa

POSSIBLE CAUSE

Harness or connector (Primary pressure solenoid valve circuit is open or shorted)
Primary pressure solenoid valve

FAIL-SAFE

When a malfunction occurs on the low oil pressure side

Selector shock is large
Start is slow
Acceleration is slow
Lock-up is not performed

When a malfunction occurs on the high oil pressure side

Selector shock is large
Lock-up is not performed

DTC CONFIRMATION PROCEDURE

1.PREPARATION BEFORE WORK

If another "DTC CONFIRMATION PROCEDURE" occurs just before, turn ignition switch OFF and wait for at least 10 seconds, then perform the next test.

>> GO TO 2.

2.CHECK DTC DETECTION

Start the engine.
Drive the vehicle.
Maintain the following conditions for 20 seconds or more.

Vehicle speed : 40 km/h (25 MPH) or more

Stop the vehicle.
Check the first trip DTC.

Is “P0965”detected? YES >> Go to TM-162, "Diagnosis Procedure".

NO-1 >> To check malfunction symptom before repair: Refer to GI-41, "Intermittent Incident".

NO-2 >> Confirmation after repair: INSPECTION END

Diagnosis Procedure

1.REPLACE TRANSAXLE ASSEMBLY

Replace transaxle assembly. Refer to TM-220, "Removal and Installation".

>>WORK END

P0963 pressure control solenoid A

DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P0963 PC SOLENOID A(Pressure Control Solenoid A Control C ...

P0966 pressure control solenoid B

DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P0966 PC SOLENOID B (Pressure Control Solenoid B Contr ...

Other materials:

B1431 seat belt pre-tensioner
DTC Logic DTC DETECTION LOGIC CONSULT name DTC DTC detecting condition Repair order FRONT PRE-TEN RH CIRCUIT [OPEN] B1431 RH seat belt pre-tensioner circuit is open. Refer to SRC-61, "Diagnosis Procedure" FRONT PRE-TEN RH CIRC ...

Removal and installation
FRONT AIR CONTROL Removal and Installation REMOVAL Release the front air control clips and pawls using a suitable tool. : Metal clip : Pawl Disconnect the harness connector from the front air control (1) and remove. INSTALLATION Installation is in the reverse order of ...

Active ride control
This system senses upper body motion (based on wheel speed information) and controls engine torque and four wheel brake pressure. This will enhance ride comfort in effort to restrain uncomfortable upper body movement when passing over undulated road surfaces . This system comes into effect abo ...