Nissan Rogue manuals

Nissan Rogue Service Manual: P2014, P2016, P2017, P2018 intake manifold runner control valve position sensor

Nissan Rogue Service Manual / Engine / Engine Control System / DTC/Circuit diagnosis / P2014, P2016, P2017, P2018 intake manifold runner control valve position sensor

DTC Description

DTC DETECTION LOGIC

DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detecting condition
P2014 IN/MANIFOLD RUNNER POS SEN B1 (Intake manifold runner position sensor/ switch circuit bank 1) An excessively low voltage from the sensor is sent to ECM.
P2016 IN/MANIFOLD RUNNER POS SEN B1 (Intake manifold runner position sensor/ switch circuit low bank 1)
P2017 IN/MANIFOLD RUNNER POS SEN B1 (Intake manifold runner position sensor/ switch circuit high bank 1) An excessively high voltage from the sensor is sent to ECM.
P2018 IN/MANIFOLD RUNNER POS SEN B1 (Intake manifold runner position sensor/ switch circuit intermittent bank 1)

POSSIBLE CAUSE

FAIL-SAFE

Not applicable

DTC CONFIRMATION PROCEDURE

1.CHECK DTC PRIORITY

If DTC P2014, P2016, P2017 or P2018 is displayed with DTC P0643, first perform the trouble diagnosis for DTC P0643.

Is applicable DTC detected? YES >> Perform diagnosis of applicable. Refer to EC-379, "DTC Description".

NO >> GO TO 2.

2.PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following before conducting the next test.

  1.  Turn ignition switch OFF and wait at least 10 seconds.
  2.  Turn ignition switch ON.
  3.  Turn ignition switch OFF and wait at least 10 seconds.

TESTING CONDITION: Before performing the following procedure, confirm that battery voltage is more than 11 V at idle. >> GO TO 3.

3.PERFORM DTC CONFIRMATION PROCEDURE

  1.  Start engine and let it idle for 10 seconds.
  2.  Check 1st trip DTC.

Is 1st trip DTC detected? YES >> Proceed to EC-424, "Diagnosis Procedure".

NO >> INSPECTION END

Diagnosis Procedure

1.CHECK DTC PRIORITY

If DTC P2014, P2016, P2017 or P2018 is displayed with DTC P0643, first perform the trouble diagnosis for DTC P0643.

Is applicable DTC detected? YES >> Perform diagnosis of applicable. Refer to EC-379, "DTC Description".

NO >> GO TO 2.

2.CHECK INTAKE MANIFOLD RUNNER CONTROL VALVE POSITION SENSOR POWER SUPPLY

  1. Turn ignition switch OFF.
  2.  Disconnect intake valve manifold runner control valve position sensor harness connector.
  3.  Turn ignition switch ON.
  4.  Check the voltage between intake valve manifold runner control valve position sensor harness connector.

Check intake manifold runner control valve position sensor power supply

Is the inspection result normal? YES >> GO TO 5.

NO >> GO TO 3.

3.CHECK INTAKE MANIFOLD RUNNER CONTROL VALVE POSITION SENSOR POWER SUPPLY CIRCUIT

Check the voltage between intake valve manifold runner control valve position sensor harness connector and ground.

Check intake manifold runner control valve position sensor power supply circuit

Is the inspection result normal? YES >> GO TO 4.

NO >> Perform the trouble diagnosis for power supply circuit.

4.CHECK ECM GROUND CIRCUIT

  1. Turn ignition switch OFF.
  2.  Disconnect ECM harness connector.
  3.  Check the continuity between ECM harness connector and ground.

Check ECM ground circuit

  1. Also check harness for short to power.

Is the inspection result normal? YES >> GO TO 8.

NO >> Repair or replace error-detected parts.

5.CHECK INTAKE MANIFOLD RUNNER CONTROL VALVE POSITION SENSOR GROUND CIRCUIT

  1. Turn ignition switch OFF.
  2.  Disconnect ECM harness connector.
  3.  Check the continuity between intake manifold runner control valve position sensor harness connector and ECM harness connector.

Check intake manifold runner control valve position sensor ground circuit

  1. Also check harness for short to power.

Is the inspection result normal? YES >> GO TO 6.

NO >> Repair or replace error-detected parts.

6.CHECK INTAKE MANIFOLD RUNNER CONTROL VALVE POSITION SENSOR INPUT SIGNAL CIRCUIT

  1.  Check the continuity between intake manifold runner control valve position sensor harness connector and ECM harness connector.

Check intake manifold runner control valve position sensor input signal circuit

  1. Also check harness for short to ground and to power.

Is the inspection result normal? YES >> GO TO 7.

NO >> Repair or replace error-detected parts.

7.CHECK INTERMITTENT INCIDENT

Perform GI-41, "Intermittent Incident".

Is the inspection result normal? YES >> Replace intake manifold assembly. Refer to EM-26, "Exploded View".

NO >> Repair or replace error-detected parts.

8.CHECK INTERMITTENT INCIDENT

Refer to GI-41, "Intermittent Incident".

>> INSPECTION END

P2004 intake manifold runner control valve
DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detecting condition P2004 TUMBLE CONT/V (Intake manifold runner contro ...

P2096, P2097 A/F sensor 1
DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detecting condition P2096 POST CATALYST FUEL TRIM SYS B1 (Post catalys ...

Other materials:

Precaution
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along with a front seat belt, helps to reduce the risk or severity of injury to the ...

Front grille
Exploded View Front bumper fascia Front camera (if equipped) Front grille Front emblem Pawl Clip Removal and Installation REMOVAL  Remove front grille upper clip (A) (LH/RH). Release clips and pawls, then remove front grille. : Clip : Pawl Disco ...

System
MOONROOF MOONROOF : System Diagram MOONROOF & SUNSHADE MOONROOF : System Description MOONROOF SYSTEM INPUT/OUTPUT SIGNAL CHART Item Input signal to moonroof motor assembly Moonroof motor function Actuator Moonroof switch Moonroof signal (tilt ...

© 2014-2019 Copyright www.nirogue.com