Nissan Rogue Service Manual: C1155 brake fluid level switch
DTC Logic
DTC DETECTION LOGIC
| DTC | Display Item | Malfunction detected condition | Possible causes |
| C1155 | BR FLUID LEVEL LOW | When brake fluid level low signal is detected |
|
DTC CONFIRMATION PROCEDURE
1.CHECK SELF-DIAGNOSTIC RESULT
With CONSULT.
- Turn ignition switch OFF to ON and wait 1 minute or more.
- Perform self-diagnostic result.
Is DTC C1155 detected? YES >> Proceed to diagnosis procedure. Refer to BRC-99, "Diagnosis Procedure".
NO >> Inspection End.
Diagnosis Procedure
Regarding Wiring Diagram information, refer to BRC-57, "Wiring Diagram".
1.CHECK BRAKE FLUID LEVEL
- Turn the ignition switch OFF.
- Check brake fluid level. Refer to BR-8, "Inspection".
Is the inspection result normal? YES >> GO TO 2.
NO >> Refill brake fluid. Refer to BR-16, "Drain and Refill".
2.CONNECTOR INSPECTION
- Turn ignition switch OFF.
- Disconnect combination meter connector M76 and brake fluid level switch connector E63.
- Check connectors and terminals for deformation, disconnection, looseness or damage.
Is the inspection result normal? YES >> GO TO 3.
NO >> Repair or replace as necessary.
3.CHECK BRAKE FLUID LEVEL SWITCH
Check brake fluid level switch. Refer to BRC-100, "Component Inspection".
Is the inspection result normal? YES >> GO TO 4.
NO >> Replace reservoir tank. Refer to BR-28, "Disassembly and Assembly".
4.CHECK BRAKE FLUID LEVEL SWITCH CIRCUIT
- Turn the ignition switch OFF.
- Disconnect brake fluid level switch harness connector.
- Disconnect combination meter harness connector.
- Check continuity between brake fluid level switch harness connector and combination meter harness connector.
- Check continuity between brake fluid level switch harness connector and ground.
Is the inspection result normal? YES >> GO TO 5.
NO >> Repair or replace malfunctioning components.
5.CHECK BRAKE FLUID LEVEL SWITCH GROUND CIRCUIT
Check continuity between brake fluid level switch harness connector and ground.
Is the inspection result normal? YES >> GO TO 6.
NO >> Repair or replace malfunctioning components.
6.CHECK COMBINATION METER
Check if indication and operation of combination meter are normal. Refer to MWI-8, "METER SYSTEM : System Description".
Is the inspection result normal? YES >> Replace ABS actuator and electric unit (control unit). Refer to BRC-136, "Removal and Installation".
NO >> Replace combination meter. Refer to MWI-82, "Removal and Installation".
Component Inspection
1.CHECK BRAKE FLUID LEVEL SWITCH
- Turn the ignition switch OFF.
- Disconnect brake fluid level switch harness connector.
- Check continuity between terminals of brake fluid level switch.
Is the inspection result normal? YES >> Inspection End.
NO >> Replace reservoir tank. Refer to BR-28, "Disassembly and Assembly".
C1144 incomplete steering angle sensor adjustment
DTC Logic
DTC DETECTION LOGIC
DTC
Display Item
Malfunction detected condition
Possible causes
C1144
ST ANG SEN SIGNAL
When neutral position adjustment of steering angl ...
C1160 DECEL G SEN SET
DTC Logic
DTC DETECTION LOGIC
DTC
Display Item
Malfunction detected condition
Possible causes
C1160
DECEL G SEN SET
When calibration of yaw rate/side/decel G sensor is ...
Other materials:
Precaution
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT
BELT
PRE-TENSIONER"
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT
PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the
...
Front washer nozzle and tube
Exploded View
Cowl top cover
Front washer tube
Front washer nozzle (LH)
Front washer nozzle (RH)
Pawl
Clip
Exploded View
Cowl top cover
Front washer tube
Clip
Removal and Installation - Front Washer Nozzle
REMOVAL
Remove front wiper arms (LH ...
Sunshade motor assembly
Removal and Installation
REMOVAL
Remove the headlining. Refer to. INT-30, "Removal and Installation".
Disconnect the harness connector (A) from the sunshade motor
assembly (1).
Remove sunshade motor assembly screws (B).
Remove the sunshade motor assembl ...