Nissan Rogue Service Manual: DTC/circuit diagnosis
B2600-46 CONFIG ERROR
DTC Description
DTC DETECTION LOGIC
|
DTC |
Trouble diagnosis (Trouble diagnosis contents) |
Detecting condition |
| B2600-46 | CONFIG ERROR (Configuration error) | When errors are detected in the configuration data stored in the BCM (CAN gateway function). |
POSSIBLE CAUSE
BCM
FAIL-SAFE
Transmission and reception of the signal between CAN communication circuit 1 and CAN communication circuit 2 are stopped
DTC CONFIRMATION PROCEDURE
1.PERFORM DTC CONFIRMATION PROCEDURE
With CONSULT
- Turn ignition switch ON and wait at least 2 seconds or more.
- Select “Self Diagnostic Result” mode of “CAN GATEWAY” using CONSULT.
- Check DTC.
Is DTC B2600-46 detected? YES >> Proceed to LAN-78, "Diagnosis Procedure".
NO-1 >> To check malfunction symptom before repair: GI-41, "Intermittent Incident".
NO-2 >> Confirmation after repair: INSPECTION END
Diagnosis Procedure
1.PERFORM DTC CONFIRMATION PROCEDURE AGAIN
- Turn ignition switch ON.
- Erase DTC.
- Perform DTC confirmation procedure again. Refer to LAN-78, "DTC Description".
- Check DTC.
Is DTC B2600-46 detected again? YES >> Replace BCM. Refer to the following.
- WIth Intelligent Key system: BCS-75, "Removal and Installation".
- WIthout Intelligent Key system: BCS-135, "Removal and Installation".
NO >> INSPECTION END
B2600-55 CONFIG ERROR
DTC Description
DTC DETECTION LOGIC
|
DTC |
Trouble diagnosis (Trouble diagnosis contents) |
Detecting condition |
| B2600-55 | CONFIG ERROR (Configuration error) | When no data are stored in the BCM (CAN gateway function). |
POSSIBLE CAUSE
- Configuration is incomplete
- BCM
FAIL-SAFE
Transmission and reception of the signal between CAN communication circuit 1 and CAN communication circuit 2 are stopped
DTC CONFIRMATION PROCEDURE
1.PERFORM DTC CONFIRMATION PROCEDURE
With CONSULT
- Turn ignition switch ON and wait at least 2 seconds or more.
- Select “Self Diagnostic Result” mode of “CAN GATEWAY” using CONSULT.
- Check DTC.
Is DTC B2600-55 detected? YES >> Proceed to LAN-79, "Diagnosis Procedure".
NO-1 >> To check malfunction symptom before repair: GI-41, "Intermittent Incident".
NO-2 >> Confirmation after repair: INSPECTION END
Diagnosis Procedure
1.PERFORM CONFIGURATION OF CAN GATEWAY
Perform CAN gateway configuration. Refer to LAN-77, "Work Procedure".
>> GO TO 2.
2.PERFORM DTC CONFIRMATION PROCEDURE AGAIN
- Turn ignition switch ON.
- Perform DTC confirmation procedure again. Refer to LAN-79, "DTC Description".
- Check DTC.
Is DTC B2600-55 detected again? YES >> Replace BCM. Refer to the following.
- WIth Intelligent Key system: BCS-75, "Removal and Installation".
- WIthout Intelligent Key system: BCS-135, "Removal and Installation".
NO >> INSPECTION END
Basic inspection
CONFIGURATION (CAN GATEWAY)
Work Procedure
1.WRITING MODE SELECTION
CONSULT Configuration
Select “Re/programming, Configuration” of CAN gateway.
When writing saved data>>GO TO 2.
W ...
CAN system (type 1)
DTC/CIRCUIT DIAGNOSIS
MAIN LINE BETWEEN IPDM-E AND DLC CIRCUIT
Diagnosis Procedure
1.CHECK CONNECTOR
Turn the ignition switch OFF.
Disconnect the battery cable from the negative t ...
Other materials:
P0746 pressure control solenoid A
DTC Description
DTC DETECTION LOGIC
DTC
CONSULT screen terms
(Trouble diagnosis content)
DTC detection condition
P0746
PC SOLENOID A
(Pressure Control Solenoid A Performance/
Stuck Off)
The detecting condition A or detection condition B is detected twice
or ...
Removal and installation
BCM (BODY CONTROL MODULE)
Removal and Installation
CAUTION:
Before replacing the BCM, perform “READ CONFIGURATION” to save or print current
vehicle specification.
Refer to BCS-120, "ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT (BCM) : Work
Procedure".
REMOVAL
Disc ...
P0462, P0463 fuel level sensor
DTC Description
DTC DETECTION LOGIC
This diagnosis indicates the former, to detect open or short circuit
malfunction.
DTC No.
CONSULT screen terms
(Trouble diagnosis content)
DTC detecting condition
P0462
FUEL LEVL SEN/CIRC
(Fuel level sensor ″A″ circu ...