Nissan Rogue Service Manual: P1715 input speed sensor
Description
ECM receives input speed sensor signal from TCM through CAN communication line. ECM uses this signal for engine control.
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms (Trouble diagnosis content) | DTC detecting conditio |
| P1715 | IN PULY SPEED (IN PULY SPEED) | Input speed sensor signal is different from the theoretical value calculated by ECM from output speed sensor signal and engine rpm signal. |
POSSIBLE CAUSE
- Harness or connectors (The CAN communication line is open or shorted.)
- Harness or connectors (Input speed sensor circuit is open or shorted.)
- TCM
FAIL-SAFE
Not applicable
DTC CONFIRMATION PROCEDURE
1.CHECK DTC PRIORITY
If DTC P1715 is displayed with DTC UXXXX, P0335, P0340, P0603, P0604, P0605, P606, P0607, P060A, or P060B, first perform the trouble diagnosis for DTC UXXXX, P0335, P0340, P0603, P0604, P0605, P606, P0607, P060A, or P060B.
Is applicable DTC detected? YES >> Perform diagnosis of applicable. Refer to EC-93, "DTC Index".
NO >> GO TO 2.
2.PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following before conducting the next test.
- Turn ignition switch OFF and wait at least 10 seconds.
- Turn ignition switch ON.
- Turn ignition switch OFF and wait at least 10 seconds.
>> GO TO 3.
3.PERFORM DTC CONFIRMATION PROCEDURE
- Start engine and drive the vehicle at more than 50 km/h (31 MPH)
for at least 5 seconds.
CAUTION: Always drive vehicle at a safe speed.
- Check 1st trip DTC.
Is 1st trip DTC detected? YES >> Proceed to EC-416, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis Procedure
1.CHECK DTC PRIORITY
If DTC P1715 is displayed with DTC UXXXX, P0335, P0340, P0603, P0604, P0605, P606, P0607, P060A, or P060B, first perform the trouble diagnosis for DTC UXXXX, P0335, P0340, P0603, P0604, P0605, P606, P0607, P060A, or P060B.
Is applicable DTC detected?
YES >> Perform diagnosis of applicable. Refer to EC-93, "DTC Index".
NO >> GO TO 2.
2.CHECK DTC WITH TCM
Check DTC with TCM. Refer to TM-47, "CONSULT Function".
Is the inspection result normal? YES >> GO TO 3.
NO >> Perform trouble shooting relevant to DTC indicated.
3.REPLACE TCM
Replace TCM. Refer to TM-202, "Removal and Installation".
>> INSPECTION END
P1574 ASCD vehicle speed sensor
Description
The ECM receives two vehicle speed sensor signals via CAN communication line.
One is sent from combination
meter, and the other is from TCM (Transmission control module). The ECM uses ...
P1805 brake switch
DTC Description
DTC DETECTION LOGIC
DTC No.
CONSULT screen terms
(Trouble diagnosis content)
DTC detecting condition
P1805
BRAKE SW/CIRCUIT
(BRAKE SW/CIRCUT)
A stop ...
Other materials:
Moonroof switch
Removal and Installation
REMOVAL
Remove map lamp assembly. Refer to INL-55, "Removal and Installation".
Using a suitable tool release clip from harness connector.
: Clip
Using a suitable tool release pawls and remove moonroof switch
finisher (1).
Using a ...
Power supply and ground circuit
COMBINATION METER
COMBINATION METER : Diagnosis Procedure
Regarding Wiring Diagram information, refer to MWI-32, "Wiring Diagram".
1.CHECK FUSES
Check that the following fuses are not blown.
Is the fuse blown?
YES >> Replace the blown fuse after repairing the affected circu ...
Forward-facing child restraint installation
using LATCH
For additional information, refer to all Warnings
and Cautions in the “Child Safety” and “Child
Restraints” sections before installing a child restraint.
NISSAN does not recommend the use of the
lower anchors if the combined weight of the child
and the child restraint exceeds 65 lbs ( ...